check oil AUDI A6 2000 C5 / 2.G AHA ATQ Engines Valve Gear Service Manual

15-3


Cylinder head without oil lines to camshaft
bearings

1 -
Double bearing cap
Lightly coat with sealant 454 300 02 A2
before installing page 15
-36

2 -
Bolt
10 Nm (7ft lb)
3 -
Exhaust camshaft bearing cap Watch guide sleeveNote installation position and numbering
page 15
-36

Lightly coat last bearing cap (after chain)
with D454 300 A2 sealant before installing
4 -
Exhaust camshaft Checking axial clearance page 15
-42
Removing and installing page 15
-31

Check radial clearance using Plastigage
(hydraulic valve lifters removed):
Wear limit: 0.1 mm (0.004 in.)Max. run-out: 0.01 mm (0.0004 in.)
Pa
ge 3 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1

15-5


11 -
Hydraulic valve lifter (intake)
Notes page 15
-45
12 -
Valve keepers
13 -
Valve spring retainer
14 -
Valve spring
15 -
Valve stem oil seal
Replacing with cylinder head installed
page 15
-47

16 -
Rubber/metal seal
Always replace
17 -
Seal Always replace
18 -
Cylinder head Removing and installing page 15
-18
Checking for distortion page 15
-27
Resurfacing page 15
-28
19 -
Exhaust valve
20 -
Intake valve
21 -
Oil seal
Camshaft Position (CMP) sensor side
Pa
ge 5 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1

15-8


5 -
Exhaust camshaft
Checking axial clearance page 15
-42
Removing and installing page 15
-31

Check radial clearance using Plastigage
(hydraulic valve lifters removed):
Wear limit: 0.1 mm (0.004 in.)Max. run-out: 0.01 mm (0.0004 in.)
6 -
Cap Always replace
7 -
Oil line Intake sideFrom VIN 8D-W-005 001Note installed position Fig. 3For bearing cap lubrication
8 -
Intake camshaft bearing cap With oil line connectorNote installation position and numbering
page 15
-36

Pa
ge 9 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1

15-10


15 -
Valve spring retainer
16 -
Valve spring
17 -
Valve stem oil seal
Replacing with cylinder head installed
page 15
-47

18 -
Rubber/metal seal
Always replace
19 -
Seal Always replace
20 -
Cylinder head Removing and installing page 15
-18
Checking for distortion page 15
-27
Resurfacing page 15
-28
21 -
Exhaust valve
22 -
Intake valve
23 -
Oil seal
Camshaft Position (CMP) sensor sideReplacing page 15
-14
Pa
ge 11 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1

15-29

Compression, checking


Test conditions

Engine oil temperature at least 30 C

Battery fully charged

- Disconnect harness connectors from all 6 fuel
injectors.

- Disconnect 5-pin harness connector from power
output stage of ignition coils.

- Open throttle fully.

- Use VAG1381 or VAG1763 compression tester
to check compression.

- Operate starter until no further pressure
increases are indicated by VAG1381 or
VAG1763 compression tester.

Compression pressure
New
Wear
limit Max. permissable
difference between
cylinders
Pa
ge 34 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1

15-46


Note:
If irregular valve noise occurs repeatedly during short journeys and
disappears after extended driving, the oil check valves must be replaced
page 17
-9 . - Push down on valve lifters using wood or plastic wedge. If 0.20 mm
(0.008 in.) feeler gauge can be inserted between camshaft and valve
lifter, replace valve lifter.
Pa
ge 53 of 62 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.15.1